Hardware-in-the-loop (HIL) testing is only as good as your access to the signals on the control module under test. Cut into the harness to probe a pin and you risk the very wiring integrity you're trying to validate; skip the probing and you lose the fault-injection and signal-tracing that make HIL worth doing. At EMB Power, New Eagle's exclusive UK and EU partner for the Raptor toolchain, we fit Raptor breakout boxes into EV and hybrid HIL rigs specifically to remove that trade-off. Here's how they work, which module they match, and where they fit in a validation workflow.
HIL testing bridges simulation and real hardware by letting engineers inject, monitor and manipulate sensor or actuator signals in a controlled bench environment before a control module ever sees a vehicle. For EV and hybrid programmes, that matters for four reasons: it verifies control logic before field trials, it supports functional safety sign-off, it de-risks component integration ahead of full-vehicle assembly, and it shortens the debugging and calibration loop during rapid prototyping. The practical obstacle is almost always physical: getting clean, repeatable access to every pin on the control module without damaging the harness or the connector.
A Raptor breakout box sits in-line between the vehicle or simulation harness and the control module, routing every pin out to a front-mounted banana jack. New Eagle supplies each breakout box with a matching test lead kit of patch cables, shorting bars and banana jacks, so a bench already set up with a multimeter, oscilloscope or data logger can reach any signal without touching the connector itself.
New Eagle builds breakout boxes per control module rather than as a one-size-fits-all accessory, so the right box depends on which Raptor module is on your bench. New Eagle's current breakout box range includes:
| Breakout Box | Matched Control Module(s) |
|---|---|
| 48-pin breakout box with test lead kit | GCM48 |
| 70-pin breakout box with test lead kit | GCM70, SECM70 |
| 80-pin breakout box with test lead kit | RCM80 |
| 112-pin breakout box with test lead kit | RCM112, PCM112, 0904-112 |
| 196-pin breakout box with test lead kit | ECM196, GCM196 |
Compatibility based on New Eagle's published store listings as of November 2026; confirm the current range and lead times with EMB Power before specifying a rig.
The workflow for bringing a breakout box into a bench setup is deliberately simple, which is the point — it shouldn't be the slow part of your test cycle.
In practice, teams that put a breakout box between the harness and the control module see the benefit in test-cycle time rather than in any single measurement:
EMB Power is New Eagle's exclusive UK and EU supplier of Raptor control hardware and the Raptor-Dev model-based development toolchain, and now of the OpenECU range following New Eagle's 2026 acquisition of Pi Innovo. That means UK and EU controls teams can specify the right breakout box for their specific Raptor module, get it supplied with the matching test lead kit, and draw on engineering support from a team that builds HIL rigs on this toolchain regularly — rather than working through a generic reseller who has never seen the module in question on a bench.
You need the matching one. New Eagle builds breakout boxes per module family — 48-pin for GCM48, 70-pin for GCM70, 80-pin for RCM80, 112-pin for RCM112 and related modules, and 196-pin for ECM196/GCM196 — so the connector and pinout line up exactly. EMB Power can confirm the right box for your specific module.
New Eagle supplies each breakout box together with a test lead kit — patch cables, shorting bars and banana jacks — as a single assembly, so there's no separate accessory to source for basic bench use.
It's designed to be installed and removed without tools, which is what makes it practical for HIL and prototype work — teams typically fit it for a validation campaign and remove it afterwards, leaving the original harness connection exactly as it was, rather than leaving it in a production or field vehicle.
If you're specifying a HIL rig, or need the right breakout box confirmed for your Raptor control module, contact EMB Power to talk through your test bench requirements.