Most hybrid and electric vehicle architectures don't run on one network protocol — they run on at...
Hardware-in-the-Loop Testing for EVs: Why Raptor Breakout Boxes Belong on Your Bench
Hardware-in-the-loop (HIL) testing is only as good as your access to the signals on the control module under test. Cut into the harness to probe a pin and you risk the very wiring integrity you're trying to validate; skip the probing and you lose the fault-injection and signal-tracing that make HIL worth doing. At EMB Power, New Eagle's exclusive UK and EU partner for the Raptor toolchain, we fit Raptor breakout boxes into EV and hybrid HIL rigs specifically to remove that trade-off. Here's how they work, which module they match, and where they fit in a validation workflow.
Why HIL Testing Needs Non-Destructive ECU Access
HIL testing bridges simulation and real hardware by letting engineers inject, monitor and manipulate sensor or actuator signals in a controlled bench environment before a control module ever sees a vehicle. For EV and hybrid programmes, that matters for four reasons: it verifies control logic before field trials, it supports functional safety sign-off, it de-risks component integration ahead of full-vehicle assembly, and it shortens the debugging and calibration loop during rapid prototyping. The practical obstacle is almost always physical: getting clean, repeatable access to every pin on the control module without damaging the harness or the connector.
What a Raptor Breakout Box Does on the Bench
A Raptor breakout box sits in-line between the vehicle or simulation harness and the control module, routing every pin out to a front-mounted banana jack. New Eagle supplies each breakout box with a matching test lead kit of patch cables, shorting bars and banana jacks, so a bench already set up with a multimeter, oscilloscope or data logger can reach any signal without touching the connector itself.
- Non-destructive signal access — no cutting, probing or altering the factory wiring loom
- Rapid signal tracing — every pin available from the front panel for quick measurement
- Safe fault injection — the supplied shorting bars and test leads allow deliberate open, short or fault simulation
- Tool-free installation — the box unplugs in-line, which matters when a prototype jig is being reconfigured several times a day
- Repeatable test conditions — a fixed, documented interface supports automated HIL rigs where reproducibility matters as much as the initial result
Matching the Breakout Box to Your Control Module
New Eagle builds breakout boxes per control module rather than as a one-size-fits-all accessory, so the right box depends on which Raptor module is on your bench. New Eagle's current breakout box range includes:
| Breakout Box | Matched Control Module(s) |
|---|---|
| 48-pin breakout box with test lead kit | GCM48 |
| 70-pin breakout box with test lead kit | GCM70, SECM70 |
| 80-pin breakout box with test lead kit | RCM80 |
| 112-pin breakout box with test lead kit | RCM112, PCM112, 0904-112 |
| 196-pin breakout box with test lead kit | ECM196, GCM196 |
Compatibility based on New Eagle's published store listings as of November 2026; confirm the current range and lead times with EMB Power before specifying a rig.
Building a Breakout Box into Your HIL Workflow
The workflow for bringing a breakout box into a bench setup is deliberately simple, which is the point — it shouldn't be the slow part of your test cycle.
- Select the breakout box variant that matches the control module on test.
- Power down the rig and disconnect the harness from the Raptor module.
- Insert the breakout box in-line, with the vehicle or simulation harness on one side and the control module on the other.
- Reconnect power. Every pin signal is now available at the front panel for test leads, a multimeter, an oscilloscope or a fault injector.
- Run signal monitoring, logging or fault injection per the test protocol.
- Remove the breakout box once validation is complete and reconnect directly, leaving the harness exactly as it was.
What This Means for EV and Hybrid Validation Teams
In practice, teams that put a breakout box between the harness and the control module see the benefit in test-cycle time rather than in any single measurement:
- Faster root-cause analysis — pin mapping and signal tracing become systematic instead of ad hoc
- Lower risk of wiring damage — the harness stays intact, which matters for warranty and rework budgets alike
- Reusable across programmes — once bought, a breakout box supports multiple development cycles for the same module family
- Easier automation — a fixed, documented pinout integrates cleanly with test-automation hardware and logging software
- Better cross-discipline access — controls, software and test engineers can all reach the same signals without renegotiating bench access
Why Engineering Teams Work With EMB Power
EMB Power is New Eagle's exclusive UK and EU supplier of Raptor control hardware and the Raptor-Dev model-based development toolchain, and now of the OpenECU range following New Eagle's 2026 acquisition of Pi Innovo. That means UK and EU controls teams can specify the right breakout box for their specific Raptor module, get it supplied with the matching test lead kit, and draw on engineering support from a team that builds HIL rigs on this toolchain regularly — rather than working through a generic reseller who has never seen the module in question on a bench.
FAQ
Does a Raptor breakout box work with any control module, or do I need the right one for my hardware?
You need the matching one. New Eagle builds breakout boxes per module family — 48-pin for GCM48, 70-pin for GCM70, 80-pin for RCM80, 112-pin for RCM112 and related modules, and 196-pin for ECM196/GCM196 — so the connector and pinout line up exactly. EMB Power can confirm the right box for your specific module.
Does the breakout box come with the test leads and shorting bars, or do I need to buy those separately?
New Eagle supplies each breakout box together with a test lead kit — patch cables, shorting bars and banana jacks — as a single assembly, so there's no separate accessory to source for basic bench use.
Can I leave a breakout box in place permanently, or is it a bench-only tool?
It's designed to be installed and removed without tools, which is what makes it practical for HIL and prototype work — teams typically fit it for a validation campaign and remove it afterwards, leaving the original harness connection exactly as it was, rather than leaving it in a production or field vehicle.
If you're specifying a HIL rig, or need the right breakout box confirmed for your Raptor control module, contact EMB Power to talk through your test bench requirements.